SPRINKLER IRRIGATION SYSTEM DESIGN. Study Diagram 2, a typical yard area showing positioned sprinklers. Impulse pop-up spinklers may be used if area size permits (refer to Product Guide). Now position heads in small lawn areas, parkways, and at the side of your house. These areas are usually watered by one or two rows of part circle heads.
Living landscapes need water to survive and flourish, and relying completely on natural rainfall sometimes isn't the best method of supplying water. With the convenience of spraying water directly where it needs to go, and the ability to automate your watering schedule, an underground sprinkler system might be the best irrigation for your needs. Installing your own home irrigation system can save you money. However, it's not one of the easiest do-it- yourself projects around.To decide if you really need an underground irrigation system consider:.
The type of grass in your lawn affects irrigation needs. Some turfgrass varieties have higher water requirements than others. Your soil type also affects the efficiency of irrigation. For example: sandy soils absorb water more quickly than clay. An irrigation system gives you better control of the moisture content of your soil, but if you supply more water than the soil can absorb, runoff is the result.Planning and purchasing the correct components are the keys to success. But don't be discouraged, most manufacturers of home irrigation systems have design and planning guides that simplify the job considerably.to decide whether to do it yourself or hire a pro.Before installing a permanent irrigation system, you'll need to:.
See if your locality requires a building permit. Check for underground utilities before digging. There are two measurements of water pressure, working (when the water supply is turned on) and static (when the water supply is shut off).
You'll need your working water pressure number.Checking your water pressure requires a pressure gauge. If you can't borrow one from a plumber buddy, you can. The gauge attaches to the outside faucet and provides a pressure reading in pounds per square inch (psi).
Make sure all other water faucets (indoors and out) are turned off when you take the reading.You can also get your water pressure from your local municipality, but it's likely to be an average for the neighborhood rather than for your home specifically. When you've completed all of the preliminary research, it's time to start laying out your system. Most yards have a variety of elements that have to be considered when laying out an irrigation system:.
Shrubs or other foundation plantings. Flower beds or mulched areas.
Trees. Sidewalks.
Fences and other man-made features. Slopes. Areas of sun and shadeBecause of these features, you'll most likely have to create more than one watering zone. The number of zones you need also depends on the GPM your system can supply. A zone (or circuit) is an independently contained set of pipe and sprinkler heads. Zones are determined by the physical attributes of your landscape and the capacity of your water supply. Each zone has its own control valve.A map is essential when establishing watering zones.
Begin by measuring and mapping your property to scale on graph paper. A scale of 1 inch = 10 feet is recommended.
The map should include the house and all permanent landscape features. Mark on the map where the water meter is located.Landscape features need to be clearly marked so that the installed system will water only areas with living materials and will provide complete coverage for them.
Note prevailing winds if you feel they'll affect coverage. More importantly, mark sloping areas in your lawn. If your yard is sloped, the water pressure changes (lower as the elevation increases, higher as it decreases), affecting the amount of water delivered by the sprinkler.You'll also need to draw where the manifold will be located. The manifold needs to be located in an inconspicuous spot near the water supply line. When installing a sprinkler system, 100 percent coverage is essential to avoid dry spots. In order to achieve this, overlap the spray pattern.
'Head to head' coverage refers to the sprinkler head layout that allows spray from each sprinkler head to reach the adjacent head, ensuring overlap.Each sprinkler head is designed for a specific watering need. Many are adjustable to allow targeted spot-watering without watering inorganic objects such as sidewalks, driveways or the house.Select sprinkler heads based on the coverage required. The number of zones and the sprinkler head size and style depend on the location of trees, shrubs, lawn and sidewalks. Large areas need one style, corners need another, and areas under shrubs need still another type. Your irrigation planning guide should have a list of sprinkler head types.Pop-up style lawn sprinkler heads are installed just below ground level. Set pop-up sprinkler heads so that they will not be damaged by mowers or foot traffic when retracted. The best ones are adjustable.
Shrub sprinklers are taller for use in flower and shrub beds. When selecting the proper height to install, keep in mind the mature size of the plants.Remember:. Pressure loss in the system causes uneven watering. To avoid unnecessary pressure loss, plan the irrigation pipe layout with as few turns as possible. Long extensions of pipe also reduce water pressure. It's better to create another zone than to overextend a single one. Mixing head types in one zone decreases efficiency.
![Fire sprinkler flow rate Fire sprinkler flow rate](/uploads/1/2/4/3/124364936/427710899.png)
Always use the same type of head for each zone. Done with the planning? Take your water measurements and maps with you when shopping for parts.You must select your system components to match your water supply and water pressure.
A mismatch will either overstress the system or provide insufficient irrigation. Valves open and close pipes to allow watering of each zone. Valve Box - Protects valves while providing easy access. Head styles vary based on the water requirements of the plantings and your water supply. Sprinkler heads are rated according to the GPM they can supply water at your particular psi. Risers connect pipe to sprinkler heads. Fittings or couplings, such as tees and elbows, connect and redirect pipe.
A manual control should be able to maintain several areas with differing needs. A backflow preventer is an anti-siphon device that's required in most areas.
Timers allow presetting of the on/off function of the system. The valve manifold is the master control of the system. Pipe choice depends on the region you live in. You'll use either PVC or polyethylene pipe. Polyvinyl chloride (or PVC) pipe is the most common irrigation material. The familiar rigid white material is stronger than polyethylene. Connections are made using adhesive.The alternative material is polyethylene.
Because it's flexible, it's used in colder climates to adapt to extended freeze cycles. Polyethylene comes in rolls and can be curved around natural and manmade obstacles, requiring fewer fittings than PVC. Connections are made with specially designed clamps.Both types of pipe are cut with a handsaw or pipe cutter.A machine called a pipe puller is great for installing polyethylene pipe, but requires a little expertise to operate. Unless you want to get some on-the-job training in your front lawn, this machine is perhaps best left to the pros. The design is done, the parts are selected and you are ready to dig and install.
Lay out the location of the lines with stakes and string. Place a flag or other marker where the sprinkler heads will be located.The trenches required for the system are relatively shallow — 6-12 inches deep depending on the freeze cycles and frost severity in your area. The trench must also be deep enough to allow the sprinklers to retract underground to prevent breakage from lawn machines.Dig the trench by hand or rent a trencher (a real time saver). If you choose to dig by hand, a garden spade with a square edge is the best tool to use.
A ditch spade is also pretty handy for working in a narrow space. It's advisable to hand dig in flower or shrub beds to prevent damage to plants.The trenches must be level.
If some heads are lower than others, gravity will reduce efficiency. Dig only as much as you can install in each work session. Save the sod to re-cover the trench. There are two ways to connect your irrigation system to the water supply. The valve can be connected (like a garden hose) to an existing outdoor faucet, which is usually located directly outside the house.
The system can also be directly connected to the service line. To connect directly, shut off the water supply. Between the main shut-off and the house, cut a one-inch section out of the service line. Add a compression tee fitting and an additional valve to allow the system's water supply to be controlled independently of the house system. Each zone will have its own controlling valve (only one valve per zone).
For future maintenance and repair, note which valve is for which zone.The manifold groups the valves in one area and allows all zones to be routed through one control. You will be able to run one zone at a time to maximize water pressure.The timer controls which zone is being watered. Choose timers based on the number of zones you have. Keep a copy of the timer/zone assignments (much as you would keep a reference of electrical circuits in a breaker box). Timers can be programmed to run for a specified time and shut off automatically. A rain/moisture sensor feature is available to detect water levels and shut on and off when needed — a great way to water when you're away from home.
Some areas require these sensors as part of an irrigation system.Many timers come equipped with WI-FI connectivity and can automatically regulate your watering schedule based on current weather. Some can even create detailed reports on water usage and soil conditions. With the ability to control these timers from a tablet or handheld device, they make a perfect.
You probably want 1-2 inches of water per week, depending on your vegetation. Measure water by placing a cup or other container in each zone. Run the system for a regular cycle and measure the amount of water in the container. This will tell you how long your system needs to run to get the right amount of water. At the end of the season in colder regions, you may need to blow out residual water from the system before the ground freezes. Compressed air is the normal 'tool' used.
Find a pro to do this task. Exposed backflow preventers and valves may need to be protected from freezing. Part of your ongoing maintenance program is observation. Don't wait for brown spots to appear to look for a clogged sprinkler head or pipe. You may need to prepare your system for winter to avoid damaging or breaking pipes and connections. In temperate and warm regions, you may get away with simply covering above-ground piping with insulation (in these climates, the ground doesn't get cold enough to freeze). For colder climates, this winterization process can be a DIY job, but especially for larger landscapes, it might be beneficial to hire a professional.To ensure your system is properly protected check with owner's manual or with the manufacturer for best practices.To Winterize:1.
Check to see if your system has auto-drain valves. If so, simply turn off water supply, open valves and allow excess water to drain from the system. This one step is sufficient to winterize underground irrigation systems with auto-drain.2.
If you have manual drains you will need to use an with pressure between 50-100 PSI. Small air compressor with lower PSI will not be able to clear water from your system.3. Open valve manifolds to allow any remaining water to drain.4.
Hook air compressor and run air through each the zone in your system until you've cleared all zones of water.5. Be sure to remember to turn off timer to avoid additional water from entering the system.